Switch menu

Re-Injection of Water Formation and Water Surface Treatment Technologies and Field Practices Training

From $5250 per attendee

Email Course
Enquire About This Course In House Training

Available Courses

  • Dubai

    14 October, 2024 - 18 October, 2024

    Enquire

  • London

    11 November, 2024 - 15 November, 2024

    Book Course

  • Houston

    9 June, 2025 - 13 June, 2025

    Book Course

Course Information

  • Course Content
  • Course Description
  • Course Objectives
  • Who Should Attend
  • CPD Unit

Course Content

Section I:  Introduction

  • The Production Facilities
  • The Engineering System Concept
  • Production Facilities Types
  • The role of Production Optimization Techniques
  • Scope of the Course
  • Initial Test

Section II: Fluid Properties, Basic Concepts, Definitions and Terminologies

  • Production Mechanisms in Reservoirs
  • Basic Principles
  • Specific Gravity, Density and Viscosity
  • Flash Calculations
  • Characterization of Flow Stream
  • Approximate Flash Calculations
  • Reservoir From a Phase behavior point of View
  • Composition and types of Natural Gas
  • Field Life and Production Profile
  • Definition process streams
  • Well fluid characteristics
  • Crude oil characteristics

Section III: Oilfield Processing Methods

Processing Systems    

  • Separation systems
  • Water treatment and disposal

Heavy Oil Production Facilities

  • Case History presentation and brief discussion
  • Diluent Distribution System
  • Case History: Diluent Model Application       

Section IV: Process Equipment Selection and Technology

  • Two-Phase Oil and gas separation
  • Factor Affecting Separation
  • Equipment Description
  • Horizontal separators
  • Vertical separators
  • Spherical Separators
  • Other Configurations
  • Scrubbers
  • Horizontal vs. Vertical Vessels Selection
  • Potential Operating Problems
  • Foamy
  • Paraffin
  • Scales
  • Sand
  • Liquid Carryover
  • Gas Blowby
  • Theory
  • Settling, Drop Size, Retention Time and Re-Entrainment
  • Separator Sizing Calculation
  • Examples:
  • Sizing a Vertical Separator
  • Sizing a Horizontal Separator
  • Desanding
  • Emulsion treatment and oil dehydration
  • Oil dehydration technology

Section V:  OIL AND WATER SEPARATION PROCESSES

  • Introduction
  • Equipment Description
  • Vessel Internals:
  • Coalescing Plates
  • Sand Jets
  • Drains
  • Emulsions
  • Theory
  • Gas separation
  • Oil/water Settling
  • Water Droplet size in oil
  • Oil Droplet in Water
  • Retention time
  • Separation Sizing:
  • Horizontal Separation Settling Equation
  • Sizing a Horizontal Three-phases Separator

Section VI: Crude Oil Treatment Systems

  • Emulsion treatment theory
  • Gravity Separation
  • Treatment equipment
  • Equipment Sizing and Theory
  • Design Procedures
  • Examples

SECTION VII: Chemical Water Analysis Pattern and Water 

                Selection, Water treatment for Injection

  1. a.       Selection of Water Sources
  2. b.      Estimation of Water requirements
  3. c.       Source Water Quality
  4. d.      Analyzing compatibility of the Water
  5. e.      Chemical Water Analyze Patterns
  6. f.        Water Treatment for Injection System

Section VIII:  Produced Water Treatment

  • Introduction
  • System Description
  • Theory
  • Treatment equipment
  • Settling Tanks and Skimmer Vessel
  • Skimmer/Coalescers
  • Plate Coalescers
  • Skimmer/Coalescers
  • Precipitator/Coalescer Filters
  • Free-Flow turbulent Coalescers
  • Floatation Units
  • Hydrocyclones
  • Disposal Piles
  • Influent Water Quality
  • Produced Water Disposal technology and new research
  • Example: Design the Produced Water Treatment System

Section IX: Pressure Analysis in Injection Wells and Management of Injection Wells

  • Pressure Fall-off Analysis, Liquid filled reservoirs
  • Variable Rate Test
  • Hall Plots Application and Analysis for Injection well performance
  • Water Injection Profiling:
  • Radioactive Surveys
  • Temperature Profiling
  • Prediction Injection Rates in Injection Well (Injectivity Index)
  • Case Study Discussion

Section X: WATER INJECTION OPERATIONS

  • Waterflooding Injection Well Management Control
  • Oil Production at the kick, Peak and breakthrough
  • Water Treatment Efficiency
  • Potential for Scaling Problems in the water Injection System

Section XI: DISCUSSIONS AND CONCLUSIONS.

Course Description

Re-Injection of Water Formation and Water Surface Treatment Technologies and Field Practices Training Course

This course is aimed at creating an understanding of WATER FORMATION RE-INJECTION AND WATER TREATMENT AND DISPOSAL. The course is designed to build up knowledge in the participant to understand the WATER RE-INJECTION process facilities design and Water treatment and disposal. The course studies in depth and in accordance to classic and new technology. Also the effect of Separation pressure is introduced using the engineering system concept of nodal analysis, and by using the classic flash calculations method. The calculations for pump specifications in the petroleum industry is treated in a formal and practical way.

Course Objectives

Who Should Attend

Engineers, R&D personnel and managers from upstream oil and gas Industry. Project Managers and multi-discipline engineering personnel from Contractor companies. Petroleum Engineers recently transfer to production areas, All non-petroleum engineers working as petroleum Engineers in the oil and gas industry. All personnel in refinery and petrochemical industry. Petroleum Engineer Trainees. Production Technicians working in the oil and gas industry, and Reservoir engineers without experience in the production area.

CPD Unit

Continuing Professional Development

35 HOURS CPD

Related Courses

Reservoir Management Training

This course will address all the principles of reservoir management. The reservoir management process with integrated concept, role of reservoir simulation in reservoir management and importance of reservoir surveillance and monitoring for the whole reservoir management process will be discussed. The significance of the production optimization process in addition to the economics evaluation will be incorporated. The course covers all aspects related to hydrocarbon recovery methods starting from the primary recovery and up to enhanced oil recovery. The course will focus on different aspects of reservoir management applications for new reservoirs, matured reservoirs, reservoir with small gas caps, reservoir with huge gas caps, thin oil rims, reservoirs with new infill opportunities and fractured reservoirs.

4 locations available

Applied Reservoir Engineering Training

This course is designed to provide a solid understanding of the practical methods used in Reservoir Engineering for maximizing the ultimate hydrocarbon recovery. This course covers all aspects related to Reservoir Engineering during all reservoir life cycle, starting from the primary recovery and up to enhanced oil recovery. This course will address not only the conventional applications of Reservoir Engineering but also extends to include the topics of Reservoir Simulation Engineering. In order to support participants by a wide knowledge, special topics are included such as using conventional Reservoir Engineering techniques to identify new infill opportunities, coning control with smart horizontal wells, Fracture Reservoir Simulation and enhanced oil recovery modeling.

4 locations available

Reservoir Simulation Principles and Practices Training

This training course will provide a comprehensive coverage of the simulation key topics, challenges, pitfalls and the approach to a quality result. The participants will be trained in the methods and use of simulation software for practical exercises throughout this course.

3 locations available

Advanced Well Test Analysis Training

This five days short course will equip participants with the principles of advanced well test analysis to improve interpretation skills by developing key reservoir parameters from well pressure transient tests. Emphasis will also be placed on the importance of preparation; supervision of well tests; data retrieval; quality check; and interpretation methods; applicable to vertical and horizontal wells in homogeneous, layered, fractured, and compartmentalized reservoirs.  In addition, the application of state of the art interpretation classical and computer-aided methods will be described, supported with field examples for the different well test types such as drawdown, buildup, fall-off, interference, pulse, injection and DST’s. Interpretation methods: Horner, Log-Log, type curves, will also be illustrated with practical examples.

4 locations available

Thermal Recovery Methods for Heavy Oil Fields Training

This course is designed to cover all the traditional and modern Thermal Recovery Methods used in the oil industry for Heavy Oil recovery. Perhaps no other single subject dominates the oil industry like thermal recovery. For many of oil fields, particularly where low-to-medium gravity oils are found or where the oil viscosity is unfavourable for conventional EOR methods application, Thermal Recovery Methods are the best techniques for ultimate recovery. Vast deposits of heavy oil exist in Canada, Venezuela and USA that are amenable to recovery by Thermal Recovery. Thermal Recovery is usually applied to heavy to medium oils, however these methods can be applied to any field being considered and be competitive with alternative methods. The course consider the following methods: Cycle Steam Injection, Double Injection Nitrogen-Steam, CO2-Steam Injection, Flue Gas-Steam Injection-This methods have given excellent results in China and Louisiana (USA), Steam Drive Process, Hot Water Injection Processes, In Situ Combustion Processes, Cold Heavy Oil Production with Sand (CHOPS),  Vapor Extraction Method (VAPEX) and Steam-Assisted Drainage (SAGD).

4 locations available

Enhanced Oil Recovery Training

Upon completion of this training, participants will be able to select the enhanced recovery method that best suits the conditions of the reservoir which they operate and also maximise reservoir recovery at the least cost, ensuring maximum investment efficiency. Technical challenges of enhanced oil recovery phase; increasing complexity, cost/benefit consideration, facilities modifications and personnel training will be discussed. A critical review of the emerging technologies, future R & D directions will be devoted an extensive coverage. Participants will learn to forecast reservoir performance under various EOR methods employing the proper empirical, analytical, and simulation tools.

4 locations available

Oil Reserves Calculations Training

This course will give a full overview of all aspects of Reserves and Resource Volume estimation and reporting, including detailed technical calculation and forecasting, economic effects, commercial effects, and the impact on Corporate accounting. The various Reserves reporting authorities will be discussed along with examples of the impact of Reserves volumes on Corporate reporting.

4 locations available

Gas Condensate Reservoirs Training

This course enables participants to develop skills to analyse and manage gas condensate reservoirs. It addresses phase behaviour; relative permeability varying with velocity and interfacial tension; material balance equations; well productivity and pseudo-pressure calculation for different completion strategies, condensate banking and gravity drainage; practical fluid and flow simulation models.

4 locations available

Reservoir Engineering for Non-Reservoir Engineers Training

This reservoir engineering for non-engineers training short course is useful if you want to develop a feel for hydrocarbon behaviour in the reservoir and of various recovery methods. It also provides you with specific and direct application of the process used in reservoir engineering and enhances your skills in solving reservoir engineering problems and maximizing recoverable reserves.

3 locations available

Waterflooding and Chemical Flood Processes Training

The case for Waterflooding: Waterflooding is one of the most important methods of improving recovery from oil reservoirs. This section of the course concentrates on reservoir and field operations aspects of water injection for pressure maintenance and secondary recovery. Participants will study fractional displacement theory and all methods available in the oil & gas industry to predict oil recovery. The course is a theoretical practical course where participants have to work towards solving a series of projects, and to immediately apply the concepts, mathematical principles and theories presented and learned during the course. Laptop/computers will be used to solve problems related to waterflooding. The Case for Chemical Flooding: Valuable insight has been gained through chemical floods in the past – failures as well as successes. MP and ASP methods hold the greatest potential for commercial success; polymer flooding a third option. Chemical flooding processes must be re-evaluated under the current technical and economic conditions. Chemical floods offer the only chance of commercial success in many depleted and waterflooded reservoirs. Chemical flooding is here to stay because it holds the key to maximizing the reserves in our known reservoirs

4 locations available

Paraffin and Asphaltene in the Oil and Gas Industry: Physical Characteristics, Causes of Problems and Possible Solutions Training

This course discusses the physical characterization of crude oil, gas liquids and gas. Discussions of the causes of problems in all types of wells to include oil, gas, shale oil, coal bed methane, gas storage, injection, EOR produced wells and all types of surface equipment are included. The type of problems encountered in oils from 8 ° API to 90°API caused by paraffin and asphaltenes will be discussed. Field strategies for the production of these oils from these wells and practical solutions to produce these oils are presented. Testing methods for characterizing the physical characteristics of these oils and selecting possible treatment methods are covered. Discussions of current treatment methods, Mechanical, Thermal, Chemical and Others, to reduce or eliminate problems are included. A section will be included on effects of paraffin and asphaltenes on emulsion, corrosion and scale problems. A section on selecting Cost Effective treatment methods will be included. Formation damage removal of paraffin and asphaltenes from new and mature wells will be included. Questions will be taken throughout the course and discussion of the participants own problems will be encouraged. Laboratory and Field case histories are a large part of this course.

3 locations available

Advanced Steam Injection Processes Training

Steam Injection is a thermal drive process that adds heat to the reservoir to expand the oil-in-place, reduce it viscosity, provide drive and thereby improve the displacement efficiency of injected fluid. This course explores the concepts behind steam injection processes in the field. The emphasis is the practical aspects of steam injection.  Equations and calculation methods are included in the course. There is an emphasis on the surface facilities, field practices, and operational problems. The material presented in this course is directed toward engineers, technicians, independent operators.

3 locations available

Waterflooding Technologies and Field Practices (N2/CO2/WAG) Training

This course concentrates on Reservoir and field operations aspects of waterfloooding injection for pressure maintenance and Secondary Recovery. Study in depth of Fractional Displacement theory and all methods available in the oil and gas industry to predict oil recovery. The course is a theoretical-practical course and is designed as a workshop where the participant has to work hard solving a series of projects to apply immediately the concepts, mathematical principles and theories presented and learned during the course. The participants will use a reservoir engineering software designed for water injection. The software will be provided to each participant without additional cost.

3 locations available

Water Shut-Off and Conformance Improvement Technologies Training

Approximately 20 billion barrels of water are reinjected in the US every year. Any technology that minimizes the amount of water or gas produced in conjunction with the produced oil would have a significant impact on the energy consumption and on the cost oil production. There are many factors, such as the presence of thief zones or high permeability zones, fractures and water coning which lead to an increase in water production. In an attempt to block out the undesired water production and increase the volumetric sweep efficiency of on-going waterfloods, the industry has used crosslinked polymer gels. The process involves strategically injecting a Gelling fluid into water coning well or into a high permeability watered out zone, restricting flow in that zone and redirecting water flow into the lower permeability unswept oil zones. Thus water shut off and conformance-control treatments can be used to generate relatively large volumes of incremental oil production with low costs and selectively, targeted small volume treatments, which extends the economic lives of marginal and mature wells.

4 locations available

WAG-Water Alternating-Gas EOR Processes Training

Water alternating gas (WAG) injection are improved oil recovery methods that involve three-phase fluid flow. It was originally proposed as a method to improve the sweep efficiency of gas by using water to control the mobility ratio and to stabilize the front (Caudle and Dyes, 1958; Christensen et al., 1998). WAG injection can lead to improved oil recovery by combining better mobility control and contacting upswept zones, and by leading  to  improved microscopic displacement. WAG flooding has been successfully applied to more than 60 oilfields worldwide. This course will present WAG Miscible, WAG Immiscible, WAG alternating different types of Hydrocarbon Gases and Non-HC such as N2 and CO2 Gases. Also, the course will present and study the Factors Influencing Wag Process Design such as Fluid properties and rock-fluid, Availability and composition of injection gas, Heterogeneous Permeability, Injection Pattern, Capillary pressure, Relative permeability and Wettability. A WAG Process is presented and discussed in the course as well as Field cases and Laboratory research cases and results.

3 locations available

Development of Natural Gas Field Producer Training

This course is a theoretical-practical course designed to address the basic three stages in a gas field’s life: Reserves Determination, Development and Operation of the gas field. Before planning development of an optimum producing gas field, it is necessary to determine the total reserves of the gas field as accurate as possible. After this first step, It is necessary to determine the number of wells to develop the field based on the Gas Reserves, Reservoir Pressure, Reservoir fluids and Rock Properties, Gas Reservoir Dominant Mechanisms and Gas Demand.

3 locations available

Field Development Planning Training

This short course describes all the stages field development planning, starting with the basics of oil and gas exploration; the preliminary quantification and the appraisal activities; the data requirements and integration for preparation field development plan, including wells, reservoirs, production facilities, exporting options, environmental and government regulations.  The data preparation and documentation requirements for project sanction and implementation planning will also be covered, including practical exercises and field cases studies which will be used to illustrate the methodology. On this course, the alternative options available to develop hydrocarbon resources will also be discussed, the importance of developing and integrating associated costs in onshore and offshore environments will also be addressed. In addition, Subsea facilities and drilling components will be covered, and the key drivers to optimise costs and minimise risks will also be covered. Data management and integration will also be highlighted.

5 locations available

Petroleum Reservoir Engineering Training

The aim of this short course is to provide with necessary knowledge in oil and gas reservoir engineering that introduces evaluation techniques to define characters and properties of a petroleum reservoir and helps formulate engineering solution of petroleum field related problems. Numerous engineering practices are covered. This course will help the development of a more complete “understanding” of the characteristics of oil and gas reservoirs. Data collection, integration and application directed toward maximizing recovery are stressed. Reservoir engineering equations are introduced with emphasis directed to parameter significance and an understanding of the results.

5 locations available

Integrated Reservoir Modeling Training

Integrated Reservoir Modeling is carried out to better understand and characterize uncertainties in reservoir and well behaviour. It is used to make predictions for use in hydrocarbon development planning (field development planning) and well & reservoir surveillance and optimisation. This process should be seen in the context of a business plan for a new or producing asset in which a business focus will be maintained by addressing specifically those aspects having the biggest impact or influence on the business decisions being addressed. This course therefore, explicitly cover those aspects of a study in which the business context has a strong or dominating influence e.g. framing of the project, model design, economic screening and the selection of preferred development scenarios.

3 locations available
View all course categories

Accredited Oil & Gas training courses straight to your inbox

Mobility Oil and Gas will occasionally send you marketing material about training courses.

  • This field is for validation purposes and should be left unchanged.